Im Programm von
Achtung:
Dieses Dokument unterliegt nicht dem Änderungsdienst. Der Stand entspricht der Drucklegung. Bitte informieren Sie sich vor Verwendung ob die technischen Daten noch dem aktuellen Stand entsprechen. Trotz sorgfältiger Kontrolle können wir leider keine Haftung für Druckfehler oder Irrtümer übernehmen.
G150XG03 V.0
Product Specification
AU OPTRONICS CORPORATION
www.DataSheet4U.coProduct Specification
15.0” XGA Color TFT-LCD Module
Model Name: G150XG03 V.0
Approved by
Prepared by
Martin Sun
TH Lu
GDBD Marketing Division / AU Optronics corporation
Customer
document ver 0.0
1/31
Checked & Approved by
G150XG03 V.0
Product Specification
Document version: 0.1
Date 1/20/2006
Product Specification
15.0” XGA Color TFT-LCD Module
Model Name: G150XG03
V.0
www.DataSheet4U.co
(u ) Preliminary Specifications
( ) Final Specifications
Note: This Specification is subject to change without notice.
document ver 0.0
2/31
G150XG03 V.0
Product Specification
Record of Revision
Version and
Date
Page
Old description
New Description
Remark
0.0 2005/012/22 All First Edition for Customer 0.1 2006/1/20
www.DataSheet4U.co5 6
Only define white luminance and power Add white luminance and power consumption @ 8mA IRCFL consumption @ 6.5mA IRCFL Only define white luminance @ 8mA IRCFL
Add white luminance @ 6.5mA IRCFL
15 Only define power consumption @ 8mA Add power consumption @ 6.5mA
IRCFL IRCFL 15 Only define lamp life time@ 8mA IRCFL
Add the lamp life time @ 6.5mA IRCFL
document ver 0.0
3/31
G150XG03 V.0
Product Specification
1.0 Handling Precautions
1) 2) 3) 4) 5) 6)
Since front polarizer is easily damaged, pay attention not to scratch it.
Be sure to turn off power supply when inserting or disconnecting from input connector. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press or pat the panel surface by fingers,hand or tooling.
www.Da taSheet4U.co9) Do not press the reflector sheet at the back of the module to any directions.
10) In case if a module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged.
11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT module.
12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist
nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged.
document ver 0.0
4/31
G150XG03 V.0
Product Specification
2.0 General Description
This specification applies to the 15.0 inch Color TFT/LCD Module G150XG03 V0. This module is designed for a display unit of personal computer.
The display supports the XGA (1024 (H) x 768(V)) screen format and 16.2M colors (RGB 6-bits + FRC data)/262K (RGB 6-bit) selectable
All input signals are 1 Channel LVDS interface compatible. This module does not contain an inverter card for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition:
ITEMS
Screen Diagonal
www.DataSheet4U.comActive Area Pixels H x V Pixel Pitch
Pixel Arrangement Display Mode White Luminance Contrast Ratio
Optical Rise Time/Fall Time Color Saturation
Nominal Input Voltage VDD Power Consumption
(VDD line + CCFL line) Weight
Physical Size
Unit [mm] [mm]
[mm]
[cd/m2]
[msec]
[Volt] [Watt]
[Grams] [mm]
SPECIFICATIONS 381 (15”)
304.128 (H) x 228.096 1024(x3) x 768
0.297 (per one triad) x 0.297 R.G.B. Vertical Stripe
TN mode, Normally White
250 (Typ) @ 8mA; 200nit(Typ) @ 6.5mA 500 : 1 (Typ)
12 (Typ) (Note 1) 65% NTSC (Typ) +3.3 V
13.3 W (Typ.) @8mA (Gray Bar Pattern); 11.3 W (Typ.) @6.5mA (Gray Bar Pattern) 1100 (Typ)
Min. Typ. Max. Horizatal(H) 326.0 326.5 327.0 Vertical(V) 253.0 253.5 254.0 Depth(D) - - 12.0 1 Channel LVDS
16.2M colors (RGB 6-bit + FRC data)/262k(RGB 6-bit) selectable
0 to +50 -20 to +60
Hard-coating (3H), anti-glare treatment RoHS Compliance
Electrical Interface Support Color Temperature Range Operating
Storage (Shipping) Surface Treatment ROHS
[oC] [oC]
Note 1 :System should warm up for at least one hour
document ver 0.0 5/31
G150XG03 V.0
Product Specification
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Max. Item Unit Conditions Typ. Min.
Horizontal (Right)
CR = 10 (Left) Vertical (Up) CR = 10 (Down) Horizontal (Right) CR = 5 (Left) Vertical (Up) CR = 5 (Down)
Contrast ratio
[msec]
Normal Direction Rising Time Falling Time Rising + Falling Red x Red y
Color / Chromaticity Coordinates (CIE)
Green x Green y Blue x Blue y
Color White
White Luminance @ CCFL 8mA (center)
White Luminance @ CCFL 6.5mA (center) Luminance Uniformity Crosstalk (in 75Hz) Flicker
[cd/m2] [cd/m2] [%] [%] dB
Coordinates
(CIE)
White x White y
60 60 55 45 65 65 65 65 400 - - - 0.612 0.307 0.276 0.551 0.114 0.071 0.283 0.299 200 180 75
70 70 65 55 75 75 75 75 500 8.5 3.5 12 0.642 0.337 0.306 0.581 0.144 0.101 0.313 0.329 250 200 80 1.2
- -
Note - keep total 120(Maybe 60,60)
- - - 11 5 - 0.672 0.367 0.336 0.611 0.174 0.131 0.343 0.359 1.5 -20
- Note 2 Note 3 Note 4 Note 1
-
Viewing Angle [degree]
Response Time
www.DataSheet4U.comEquipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A ,
BM 7 ,CS-1000, CA210, SR_3 & EZ Contrast(ELDIM)* )
Aperture
1∘with 50cm viewing distance
Test Point Center (VESA point 9) Environment < 1 lux Module Driving EquipmentLCD Modulemeasuring distancePR-880 /BM5A /BM7
document ver 0.0 6/31
G150XG03 V.0
Product Specification
*’ EZ Contrast is different measurement tool with very close viewing distance.
www.DataSheet4U.com
document ver 0.0 7/31
G150XG03 V.0
Product Specification
Note 1: Definition of Response time
The output signals of photo detector are measured when the input signals are changed from “Full Black” to “Full White” (rising time), and from “Full White” to “Full Black ”(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes.
% 100 90 Optical White 10 0 Tr F Tr R Black White response www.DataSheet4U.com
Note 2: Brightness uniformity of these 9 points is defined as below
Uniformity=
Minimum Luminance in 9 points (1-9)×100% Maximum Luminance in 9 Points (1-9)90 % 50 %
90 %
50 %
10 %
10 %
document ver 0.0 8/31
G150XG03 V.0
Product Specification
Note 3: Crosstalk is defined as below :
0 gray level l LA-LA’ l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B l LB-LB’ l / LB x 100%= 1.5% max., LA’ and LB’ are brightness at location A’ and B’
www.DataSheet4U.com
Note 4: Test Paterm: Subchecker Pattern at 127 gray level
R G B R G B Gray Level = L127
R G B R G B R G B R G B
document ver 0.0 9/31
A0A301/2 1/6
1/6
2/3 1/2 1/3 1/6
A A’ 1/6 1/3 1/2
B’ 2/3
1/2
B 184 gray level Unit: percentage of dimension of display area
184 gray level 30mm CA210 FFT Sub Checker Pattern Gray Level = L0
G150XG03 V.0
Product Specification
www.DataSheet4U.com
Amplitude AC DC Time
Flicker (dB)=20logAC Level(at 30 Hz) DC Level
document ver 0.0 10/31
G150XG03 V.0
Product Specification
3.0 Functional Block Diagram
The following diagram shows the functional block of the 15.0 inches wide Color TFT/LCD Module:
LVDS
+ 3.3V
www.DataSheet4U.com
AU ASIC Timing Controller G1 Y-Driver IC LVDS Receiver RSDS TransmitterTFT-LCD 1024(3)*768 Pixels X-Driver IC Mating Type: HRS DF14-20S-1.25C SM02(8.0)B-BHS-1-TB
Connector G768 D1 D3072 2 CCFL DC/DC Converter Gamma Correction DC POWER Inverter CWY20G – A0G16 / MSB240420 JST-BHR-03VS-1
document ver 0.0 11/31
G150XG03 V.0
Product Specification
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 TFT LCD Module
Item Logic/LCD Drive
Symbol VDD
Min 0.3
Max +3.6
Unit [Volt]
Conditions Note 1,2
4.2 Backlight Unit
Item CCFL Current
Symbol IRCFL
Min -
Max 8.5
Unit [mA] rms
Conditions Note 1,2
4.3 Absolute Ratings of Environment
www.DataSheet4U.com
Item
Operating Temperature Operating Humidity Storage Temperature Storage Humidity Note 1: With in Ta (25℃ )
Symbol TOP HOP TST HST
Min 0 8 -20 8
Max +50 90 +60 90
Unit [oC] [%RH] [oC] [%RH]
Conditions Note 3 Note 3 Note 3 Note 3
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard). Please refer the
graph below for the corresponding of temperature and humidity.\"
document ver 0.0 12/31
G150XG03 V.0
Product Specification
5.0 Electrical characteristics
5.1 TFT LCD Module 5.1.1 Power Specification
Input power specifications are as follows;
Symbol VDD IDD Irush PDD
www.DataSheet4U.comParameter Logic/LCD Drive Voltage VDD current LCD Inrush Current VDD Power Allowable
Logic/LCD Drive Ripple Voltage
Min 3.0 - -
Typ 3.3 600 - 2.0
Max 3.6 700 3 2.3 100
Units [Volt] [mA] [A] [Watt] [mV] p-p
±10%
Condition
Vin=3.3V , Gray Bar Pattern, at 60Hz
Note
Vin=3.3V , Gray Bar Pattern, at 60Hz
Vin=3.3V , All Black Pattern, at 75Hz
VDDrp
Note: Measurement conditions:
+5.0V+3.3V D6D5D2D1R147KGQ3AO6402F1SVCC(LCD Module Input)C11uF/16V(High to Low)Control SignalSWD1D2D5D6R2G1KC3SQ3AO6402VR147K0.01uF/25V+12.0VC21uF/25V
Vin rising time
document ver 0.0 13/31
90% 3.3V
10% 0V
470 us G150XG03 V.0
Product Specification
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.
Each signal characteristics are as follows;
Symbol VTH VTL │VID│ VICM
Parameter Differential Input High Threshold Differential Input Low Threshold Input Differential
Voltage
Differential Input Common Mode
Voltage
Min - -100 100 1.1
Typ - - 400 -
Max 100 - 600 1.45
Units [mV] [mV] [mV] [V]
Condition
VICM = 1.2V Note VICM = 1.2V Note Note VTH/VTL = ± 100mV Note
Note: LVDS Signal Waveform www.DataSheet4U.com
VTH │VID│ VTL VICM VSS
document ver 0.0 14/31
G150XG03 V.0
Product Specification
5.2 Backlight Unit
Parameter guideline for CCFL Inverter
Symbol IRCFL ICFL FCFL ViCFL (0C) (reference)
www.DataSheet4U.comViCFL
o
Parameter CCFL operation range CCFL Inrush current CCFL Frequency CCFL Ignition Voltage
Min. 2.5 - 40
Typ. 8 - 55
Max. 8.5 20 80
Unit [mA] rms [mA] [KHz] [Volt] rms
Condition (Ta=25oC) Note 4
(Ta=25oC) Note 1
1450 - -
(Ta=0oC) Note 3
(25oC) (reference) VCFL
CCFL Ignition Voltage
CCFL Discharge Voltage (Only for reference) CCFL Power consumption
1100 - -
[Volt] rms [Volt] rms
(Ta=25oC) Note 3
-
620 (@8mA) 10
710 (@2.5mA)
11
(Ta=25oC) Note 2
PCFL
@8mA(excluding inverter) CCFL Power consumption @6.5mA(excluding inverter)
-
[Watt]
8
9
(Ta=25oC) Note 2
Note 1: CCFL frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 2: Calculator value for reference (IRCFLxVCFLx2=PCFL).
Note 3: CCFL inverter should be able to give output a voltage more than 1450 volt. Lamp units need 1450 volt
minimum for ignition.
Note 4: CCFL life time is 30,000hr at 8.0mA and 50000hr at 6.5mA. It’s defined as when the brightness is reduced by
half. It’s recommended
not to exceed 8.0mA for CCFL life time concern and it’s prohibited to exceed 8.5mA for safety concern.
document ver 0.0 15/31
G150XG03 V.0
Product Specification
www.DataSheet4U.com
document ver 0.0 16/31
G150XG03 V.0
Product Specification
6.0 Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
www.DataSheet4U.com
document ver 0.0 17/31
G150XG03 V.0
Product Specification
6.2 The input data format
www.DataSheet4U.com
Note1: Please follow PSWG. Note2: 8-bit in
Note3: R/G/B data 7:MSB, R/G/B data 0:LSB
document ver 0.0 18/31
G150XG03 V.0
Product Specification
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.
CWY20G-A0D1T (PTWO) or MSB240420 (STM) Pin No. Symbol
1 2 3 4 5
6 www.DataSheet4U.com7 8 9 10 11 12 13 14 15 16 17 18 19 20
VDD VDD VSS VSS Rin0- Rin0+ VSS Rin1- Rin1+ VSS Rin2- Rin2+ VSS ClkIN- ClkIN+ VSS Rin3- Rin3+ VSS SEL68
Description
Power Supply, 3.3V (typical) Power Supply, 3.3V (typical) Ground Ground
- LVDS differential data input (R0-R5, G0) + LVDS differential data input (R0-R5, G0) Ground
- LVDS differential data input (G1-G5, B0-B1) + LVDS differential data input (G1-G5, B0-B1) Ground
- LVDS differential data input (B2-B5, HS, VS, DE) + LVDS differential data input (B2-B5, HS, VS, DE) Ground
- LVDS differential clock input + LVDS differential clock input Ground
- LVDS differential data input (R6-R7, G6-G7,B6-B7) - LVDS differential data input (R6-R7, G6-G7,B6-B7) Ground
Selection for 6 bits/8bits LVDS data input *Note1
Note 1: SEL68=”High” or “NC”, accept 6 bits LVDS data input; SEL68=”Low”, accept 8 bits LVDS data input.
document ver 0.0 19/31
G150XG03 V.0
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.
Signal Parameter Symbol MIN TYP MAX Unit Clock Timing Clock frequency clk 50 65 81 MHz Hsync Timing Horizontal active Thd 1024 1024 1024 Tclk
Horizontal blanking Thbl 30 320 1024 Tclk Horizontal period Th 1054 1344 2048 Tck
Vsync Timing Vertical active Tvd 768 768 768 Th
Vertical blanking Tvbl 8 38 256 Th Vertical period Tv 776 806 1024 Th
Note:DE mode only
Note: Typical value refer to VESA STANDARD www.DataSheet4U.com
document ver 0.0 20/31
G150XG03 V.0
Product Specification
6.4.2 Timing diagram
www.DataSheet4U.com
document ver 0.0 21/31
G150XG03 V.0
Product Specification
6.5 Power ON/OFF Sequence
Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off.
1sec min. Vin 0 V 10%90% 10ms max. 90% 10% 10% 0 min. 10% 10% www.DataSheet4U.comSignal 0 min. 0 V Lamp On
0 V 200ms
document ver 0.0 22/31
G150XG03 V.0
Product Specification
7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation Manufacturer Type Part Number
Mating Housing Part Number
Pin# www.DataSheet4U.com1 3 5 7 9 11 13 15 17 19
Signal Name VDD VSS Rin0- VSS Rin1+ Rin2- VSS ClkIN+ Rin3- VSS
2 4 6 8 10 12 14 16 18 20
Pin#
Signal Name VDD VSS Rin0+ Rin1- VSS Rin2+ ClkIN- VSS Rin3+ SEL68
Interface Connector / Interface card P-TWO or compatible
CWY20G – A0G16 / MSB240420
HRS DF14-20S-1.25C
document ver 0.0 23/31
G150XG03 V.0
Product Specification
7.1.1 Connector Illustration
www.DataSheet4U.com
document ver 0.0 24/31
G150XG03 V.0
Product Specification
7.2 Backlight Unit
Connector Name / Designation Manufacturer Type / Part Number Mating Type / Part Number For Lamp Connector JST or compatible BHR-03VS-1
SM02(8.0)B-BHS-1-TB
7.3 Signal for Lamp connector
Pin Symbol
www.DataSheet4U.com1 HV
Description Lamp High Voltage No connection Ground
2 3
NC LV
u Cable length: 140 +- 5 mm
u Connector-output position: right side (front view)
u Lamp assembly design shall be easy for replacement and repair.
document ver 0.0 25/31
G150XG03 V.0
Product Specification
8.0 Reliability
Reliability test condition
No Test Item 1 Temperature Humidity Bias (THB) 2 High Temperature Operation (HTO) 3 Low Temperature Operation (LTO) 4 High Temperature Storage (HTS) 5 Low Temperature Storage (LTS) 6 Thermal Shock Test (TST) 7 On/Off Test
8 Shock Test (Non-Operating)
www.DataSheet4U.comTest Condition 50℃, 80%, 300hours 50℃, 300hours 0℃, 300hours 60℃, 300hours -20℃, 300hours
-20℃/30min, 60℃/30min, 100 cycles On/10sec, Off/10sec, 30,000 cycles 50G, 20ms, Half-sine wave (+ X, +Y, +Z) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z)
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point Air Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point
9 Vibration Test (Non-Operating) 10 ESD (ElectroStatic Discharge)
11 Altitude Test Operation:10,000 ft Non-Operation:30,000 ft
12 Drop Test
The drop height is 60cm
document ver 0.0 26/31
G150XG03 V.0
Product Specification
9.0 Shipping and packing
9-1 Shipping label format
9-2 Carton package
www.DataSheet4U.com
document ver 0.0 27/31
G150XG03 V.0
Product Specification
10.0 Safety
10.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
10.2 Materials 10.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO Toxicologist.
10.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process.
www.DataSheet4U.comThe printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.
10.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
11.0 Other requirement
11.1 National Test Lab Requirement
The display module will satisfy all requirements for compliance to
UL 1950, First Edition CSA C22.2 No.950-M89 EEC 950 EN 60 950
U.S.A. Information Technology Equipment Canada, Information Technology Equipment International, Information Technology Equipment International, Information Processing Equipment
(European Norm for IEC950)
document ver 0.0 28/31
12.0 Mechanical Characteristics
www.DataSheet4
Ver0.2 29/31
www.DataSheet4U.com
Ver0.2 30/31
www.DataSheet4U.com
Ver0.2 31/31
因篇幅问题不能全部显示，请点此查看更多更全内容