EN301489-17 V1.3.2-2008

2022-11-30 来源：好走旅游网

ETSI EN 301 489-17 V1.3.2 (2008-04)

Harmonized European Standard (Telecommunications series)

Electromagnetic compatibilityand Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC)

standard for radio equipment;

Part 17: Specific conditions for 2,4 GHz

wideband transmission systems,

5 GHz high performance RLAN equipment and5,8 GHz Broadband Data Transmitting Systems

2 ETSI EN 301 489-17 V1.3.2 (2008-04)

Reference

REN/ERM-EMC-248-17

Keywords

EMC, HIPERLAN, LAN, radio, regulation

ETSI

650 Route des Lucioles

F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice

Individual copies of the present document can be downloaded from:

http://www.etsi.org

The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive

within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

http://portal.etsi.org/tb/status/status.asp

If you find errors in the present document, please send your comment to one of the following services:

http://portal.etsi.org/chaircor/ETSI_support.asp

No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.

TMTMTMTM

DECT, PLUGTESTS, UMTS, TIPHON, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered

for the benefit of its Members.

3GPPis a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.

ETSI

3 ETSI EN 301 489-17 V1.3.2 (2008-04)

Contents

Intellectual Property Rights................................................................................................................................5 Foreword.............................................................................................................................................................5 1 Scope........................................................................................................................................................6 2 References................................................................................................................................................6

2.1 Normative references.........................................................................................................................................6 2.2 Informative references........................................................................................................................................7

3 Definitions and abbreviations...................................................................................................................7

3.1 Definitions..........................................................................................................................................................7 3.2 Abbreviations.....................................................................................................................................................8

4 Test conditions.........................................................................................................................................8

4.1 General...............................................................................................................................................................8 4.2 Arrangements for test signals.............................................................................................................................8 4.2.1 Arrangements for test signals at the input of transmitters.............................................................................8 4.2.2 Arrangements for test signals at the output of transmitters...........................................................................8 4.2.3 Arrangements for test signals at the input of receivers.................................................................................8 4.2.4 Arrangements for test signals at the output of receivers...............................................................................9 4.2.5 Arrangements for testing transmitter and receiver together (as a system)....................................................9 4.3 Exclusion bands..................................................................................................................................................9 4.3.1 2,45 GHz RLAN equipment.........................................................................................................................9 4.3.2 5 GHz RLAN equipment..............................................................................................................................9 4.3.3 5,8 GHz Broadband data transmitting systems.............................................................................................9 4.4 Narrow band responses on receivers or receivers which are part of transceivers.............................................10 4.5 Normal test modulation....................................................................................................................................10

5 Performance assessment.........................................................................................................................10

5.1 General.............................................................................................................................................................10 5.2 Arrangements for the assessment of host dependant equipment and plug-in cards..........................................10 5.2.1 Alternative A: composite equipment..........................................................................................................10 5.2.2 Alternative B: use of a test jig or host.........................................................................................................11 5.3 Assessment procedures.....................................................................................................................................11 5.4 Ancillary equipment.........................................................................................................................................11 5.5 Equipment classification..................................................................................................................................11

6 Performance criteria...............................................................................................................................11

6.1 General performance criteria............................................................................................................................11 6.2 Performance table.............................................................................................................................................12 6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT)..............................................12 6.4 Performance criteria for Transient phenomena applied to Transmitters (TT)..................................................12 6.5 Performance criteria for Continuous phenomena applied to Receivers (CR)...................................................13 6.6 Performance criteria for Transient phenomena applied to Receivers (TR)......................................................13

7 Applicability overview...........................................................................................................................13

7.1 Emission...........................................................................................................................................................13 7.1.1 General........................................................................................................................................................13 7.1.2 Special conditions.......................................................................................................................................13 7.2 Immunity..........................................................................................................................................................13 7.2.1 General........................................................................................................................................................13 7.2.2 Special conditions.......................................................................................................................................13

Annex A (informative): Examples of radio equipment in the scope of the present document........14

A.1 Wideband transmission systems operating in the 2,4 GHz ISM band using spread spectrum

techniques...............................................................................................................................................14 A.2 Radio Local Area Networks equipment operating in the 5 GHz frequency band..................................14

ETSI

4 ETSI EN 301 489-17 V1.3.2 (2008-04)

A.3 Broadband Data Transmitting Systems operating in the band 5 725 MHz to 5 875 MHz.....................14 Annex B (informative): Annex C (informative):

The EN title in the official languages...........................................................15 Bibliography...................................................................................................17

History..............................................................................................................................................................18

ETSI

5 ETSI EN 301 489-17 V1.3.2 (2008-04)

Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: \"Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards\", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document.

Foreword

This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).

The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [3] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations.

The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Council Directive 1999/5/EC [2] of the European

Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (\"the R&TTE Directive\").

The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates

Date of adoption of this EN:

Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of this EN (dop/e):

Date of withdrawal of any conflicting National Standard (dow):

11 April 2008 31 July 2008

31 January 2009 31 July 2010

ETSI

6 ETSI EN 301 489-17 V1.3.2 (2008-04)

1 Scope

The present document, together with EN 301 489-1 [1], covers the assessment of the 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN (including HIPERLAN 1 and 2 and other) including Broadband Data Transmitting System equipment, in respect of ElectroMagnetic Compatibility (EMC).

Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for wideband data communication systems.

Examples of types of wide band data communications systems covered by the present document are given in annex A. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as stated in EN 301 489-1 [1], except for any special conditions included in the present document.

2 References

References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • •

For a specific reference, subsequent revisions do not apply.

Non-specific reference may be made only to a complete document or a part thereof and only in the following cases: - -

if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document; for informative references.

Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference.

For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the

reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE:

While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity.

2.1 Normative references

The following referenced documents are indispensable for the application of the present document. For dated

references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. [1]

ETSI EN 301 489-1 (V1.7.1): \"Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements\".

ETSI

7 ETSI EN 301 489-17 V1.3.2 (2008-04)

2.2 Informative references

The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. [2]

Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive).

Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. ETSI EN 300 328-1: \"Electromagnetic compatibility and Radio Spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Part 1: Technical characteristics and test conditions\".

ETSI EN 301 893: \"Broadband Radio Access Networks (BRAN); 5 GHz high performance

RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive\". ETSI EN 302 502: \"Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive\".

[3] [4]

[5] [6]

3 Definitions and abbreviations

3.1 Definitions

For the purposes of the present document, the terms and definitions given in EN 301 489-1 [1], clause 3 and the following apply:

Equipment Under Test (EUT): equipment under test and subject to the performance requirements of the present document

fixed station: equipment intended for use in a fixed location and fitted with one or more antennas NOTE:

The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.

hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person NOTE:

The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.

host: any equipment which has complete user functionality when not connected to the radio equipment part and to which the radio equipment part provides additional functionality and to which connection is necessary for the radio equipment part to offer functionality

plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host systems, using their control functions and power supply

stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally used on a stand-alone basis

ETSI

8 ETSI EN 301 489-17 V1.3.2 (2008-04)

3.2 Abbreviations

For the purposes of the present document, the following abbreviations apply: ACK ACKnowledgement ARQ Automatic Retransmission reQuest CR Continuous phenomena applied to Receivers CT Continuous phenomena applied to Transmitters EMC ElectroMagnetic Compatibility EUT Equipment Under Test HIPERLAN HIgh PErformance Radio Local Area Network MUS Maximum Usable Sensitivity NACK Not ACKnowledgement RF Radio Frequency TR Transient phenomena applied to Receivers TT Transient phenomena applied to Transmitters

4 Test conditions

4.1 General

For the purposes of the present document, the test conditions of EN 301 489-1 [1], clause 4, shall apply as appropriate. Further product related test conditions for wideband data communications systems are specified in clauses 4.2 to 4.5. The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases the EUT shall be exercised in a manner representative of normal intended use.

4.2

4.2.1

Arrangements for test signals

Arrangements for test signals at the input of transmitters

The provisions of EN 301 489-1 [1], clause 4.2 shall apply.

The provisions of EN 301 489-1 [1], clause 4.2.1 shall apply with the following modifications.

The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer. The transmitter shall be operated at maximum rated power.

4.2.2 Arrangements for test signals at the output of transmitters

The provisions of EN 301 489-1 [1], clause 4.2.2 shall apply with the following modifications.

The manufacturer may provide a suitable companion receiver that can be used to receive messages or to set up a communication link.

4.2.3 Arrangements for test signals at the input of receivers

The provisions of EN 301 489-1 [1], clause 4.2.3 shall apply with the following modifications. The wanted signals required to establish a communications link shall be defined by the manufacturer.

The level of the wanted signal at the input of the receiver shall be at least 30 dB above the declared Maximum Usable Sensitivity (MUS).

ETSI

9 ETSI EN 301 489-17 V1.3.2 (2008-04)

4.2.4 Arrangements for test signals at the output of receivers

The measuring equipment for the output signal from the receiver under test shall be located outside the test environment.

It shall be possible to assess the performance of the equipment by appropriately monitoring the receiver output. If the receiver has an output connector or port providing the wanted output signal, then this port shall be used via a cable, consistent with the standard cable used in normal operation, connected to the external measuring equipment outside the test environment. The measuring equipment may be supplied by the manufacturer. Precautions shall be taken to ensure that any effect on the test due to the coupling means is minimized.

The manufacturer may provide a suitable companion transmitter that can be used to transmit messages or to set up a communication link.

4.2.5

Arrangements for testing transmitter and receiver together (as a system)

The provisions of EN 301 489-1 [1], clause 4.2.5 shall apply.

The manufacturer may provide a suitable companion transceiver or transmitter and receiver that can be used to send and receive messages or to set up a communication link.

Both the EUT and the companion equipment shall transmit the normal test modulation. Further, the output of the radio equipment under test shall be monitored by the test system.

4.3 Exclusion bands

The frequencies on which the transmitter part of the EUT is intended to operate shall be excluded from conducted and radiated emission measurements when performed in transmit mode of operation.

There shall be no frequency exclusion band applied to emission measurements of the receiver part of transceivers or the stand alone receiver under test, and/or associated ancillary equipment.

The emission measurement and immunity test exclusions are referred to as \"exclusion bands\" and are defined in the clauses 4.3.1, 4.3.2 and 4.3.3 of the present document.

4.3.1 2,45 GHz RLAN equipment

The exclusion band for the transmitter and/or receiver part of the 2,45 GHz RLAN equipment under test shall extend from 2 280 MHz to 2 607,675 MHz.

4.3.2 5 GHz RLAN equipment

The exclusion band for the transmitter part of the 5 GHz RLAN equipment under test shall extend from 4 892,5 MHz to 6 011,25 MHz.

No exclusion bands applies to receive only products and the receiver part of products covered by the present document.

4.3.3 5,8 GHz Broadband data transmitting systems

The exclusion band for the transmitter part of the 5,8 GHz Broadband data transmitting systems under test shall extend from 5 438,75 MHz to 6 168,75 MHz.

No exclusion bands applies to receive only products and the receiver part of products covered by the present document.

ETSI

10ETSI EN 301 489-17 V1.3.2 (2008-04)

4.4

Narrow band responses on receivers or receivers which are part of transceivers Normal test modulation

The provision of EN 301 489-1 [1], clause 4.4 shall apply.

4.5

The modulated test signal shall represent normal intended use, and may contain data formatting, error detection and correction information.

5 Performance assessment

5.1 General

The provision of EN 301 489-1 [1], clause 5.1 shall apply with the following modification.

The manufacturer shall supply at the time of submission of the equipment for test, the information required in EN 301 489-1 [1], clause 5.1 and the following which shall be recorded in the test report: • • • • •

the operating frequency range(s) of the equipment and, where applicable, band(s) of operation; the type of the equipment, for example: stand-alone or plug-in radio device; the host equipment to be combined with the radio equipment for testing;

the minimum performance level under the application of EMC stress (see clause 6.2);

the normal test modulation, the format, the type of error correction and any control signals

e.g. ACKnowledgement (ACK)/Not ACKnowledgement (NACK) or Automatic Retransmission re Quest (ARQ).

5.2

Arrangements for the assessment of host dependant equipment and plug-in cards

For equipment parts for which integration with a host equipment is necessary in order to offer functionality, two

alternative approaches defined in clauses 5.2.1 and 5.2.2 may be used. The manufacturer shall declare which alternative shall be used.

5.2.1 Alternative A: composite equipment

A combination of the radio equipment part and a specific type of host equipment may be used for assessment according to the present document.

Where a specific combination of host equipment and a radio equipment part is tested as a composite system for compliance, repeat testing shall not be required for: -

those other combinations of hosts and radio equipment parts which are based on substantially similar host models in the circumstance that the variations in mechanical and electrical properties between such host models are unlikely to significantly influence the intrinsic immunity and unwanted emissions of the radio equipment part;

the radio equipment part which cannot be used without mechanical, electrical, or software modification in variations of host equipment different from those represented by the units for which compliance to the present document has been demonstrated.

For all other combinations, each combination shall be tested separately.

ETSI

11ETSI EN 301 489-17 V1.3.2 (2008-04)

5.2.2 Alternative B: use of a test jig or host

Where the radio equipment part is intended for use with a variety of host systems, the manufacturer shall supply a

suitable test configuration consisting of either a host system intended for normal use or a test jig that is representative of the range of host systems in which the device may be used. The test jig shall allow the radio equipment part to be

powered and stimulated in a way similar to the way it would be powered and stimulated when connected to or inserted into host equipment.

5.3 Assessment procedures

The performance assessment shall be based upon: - maintenance of function(s); - -

the way the eventual loss of function(s) can be recovered; unintentional behaviour of the EUT.

The test system shall set up a communications link in the same manner as the Equipment Under Test's (EUT) normal intended use.

Any user defined data fields in the memory or storage of the EUT shall be filled in a way representative of normal intended use.

The assessment procedure shall verify that the communications link is maintained and that there is no loss of user control functions as declared by the manufacturer or loss of the stored user defined data.

5.4 Ancillary equipment

The provision of EN 301 489-1 [1], clause 5.4 shall not apply as ancillary equipment is outside the scope of the present document.

5.5 Equipment classification

Hand portable equipment, or combinations of equipment, declared as capable of being powered for intended use by the main battery of a vehicle shall additionally be considered as vehicular mobile equipment.

Hand portable or mobile equipment, or combinations of equipment, declared as capable of being powered for intended use by ac mains shall additionally be considered as fixed station equipment.

6 Performance criteria

6.1

- - -

General performance criteria

performance criteria A for immunity tests with phenomena of a continuous nature; performance criteria B for immunity tests with phenomena of a transient nature;

performance criteria C for immunity tests with power interruptions exceeding a certain time.

The performance criteria are:

The equipment shall meet the minimum performance criteria as specified in the following clauses.

ETSI

12ETSI EN 301 489-17 V1.3.2 (2008-04)

6.2 Performance table

Table 1: Performance criteria

After test

Shall operate as intended

Shall be no degradation of performance (see note 2) Shall be no loss of function

Shall be no loss of stored data or user programmable functions

B Functions shall be self-recoverable

Shall operate as intended after recovering

Shall be no degradation of performance (see note 2) Shall be no loss of stored data or user programmable functions

C May be loss of function (one or more) Functions shall be recoverable by the operator

Shall operate as intended after recovering

Shall be no degradation of performance (see note 2)

NOTE 1: Degradation of performance during the test is understood as a degradation to a level not below a

minimum performance level specified by the manufacturer for the use of the apparatus as intended. In some cases the specified minimum performance level may be replaced by a permissible degradation of performance.

If the minimum performance level or the permissible performance degradation is not specified by the

manufacturer then either of these may be derived from the product description and documentation (including leaflets and advertising) and what the user may reasonably expect from the apparatus if used as intended.

NOTE 2: No degradation of performance after the test is understood as no degradation below a minimum

performance level specified by the manufacturer for the use of the apparatus as intended. In some cases the specified minimum performance level may be replaced by a permissible degradation of performance. After the test no change of actual operating data or user retrievable data is allowed.

If the minimum performance level or the permissible performance degradation is not specified by the

During test

Shall operate as intended

May show degradation of performance (see note 1)

Shall be no loss of function

Shall be no unintentional transmissions May show loss of function (one or more) May show degradation of performance (see note 1)

No unintentional transmissions

6.3

Performance criteria for Continuous phenomena applied to Transmitters (CT)

The performance criteria A shall apply.

Tests shall be repeated with the EUT in standby mode (if applicable) to ensure that unintentional transmission does not occur. In systems using acknowledgement signals, it is recognized that an ACKnowledgement (ACK) or Not ACKnowledgement (NACK) transmission may occur, and steps should be taken to ensure that any transmission resulting from the application of the test is correctly interpreted.

6.4

Performance criteria for Transient phenomena applied to Transmitters (TT)

The performance criteria B shall apply, except for voltage dips of 100 ms and voltage interruptions of 5 000 ms duration, for which performance criteria C shall apply.

not-acknowledgement (NACK) transmission may occur, and steps should be taken to ensure that any transmission resulting from the application of the test is correctly interpreted.

ETSI

13ETSI EN 301 489-17 V1.3.2 (2008-04)

6.5

Performance criteria for Continuous phenomena applied to Receivers (CR)

The performance criteria A shall apply.

Where the EUT is a transceiver, under no circumstances, shall the transmitter operate unintentionally during the test. In systems using acknowledgement signals, it is recognized that an ACK or NACK transmission may occur, and steps should be taken to ensure that any transmission resulting from the application of the test is correctly interpreted.

6.6

Performance criteria for Transient phenomena applied to Receivers (TR)

The performance criteria B shall apply, except for voltage dips of 100 ms and voltage interruptions of 5 000 ms duration for which performance criteria C shall apply.

7 Applicability overview

7.1 Emission

7.1.1 General

EN 301 489-1 [1], table 1 contains the applicability of EMC emission measurements to the relevant ports of radio equipment.

7.1.2 Special conditions

No special conditions shall apply to radio equipment in the scope of the present document.

7.2 Immunity

7.2.1 General

EN 301 489-1 [1], table 2, contains the applicability of EMC immunity measurements to the relevant ports of radio equipment.

7.2.2 Special conditions

No special conditions are relevant for products covered in the present document.

ETSI

14ETSI EN 301 489-17 V1.3.2 (2008-04)

Annex A (informative):

Examples of radio equipment in the scope of the present document

The present document covers radio wideband transmission systems as set out below.

A.1

Wideband transmission systems operating in the 2,4 GHz ISM band using spread spectrum techniques

Wideband transmission systems are defined in EN 300 328-1 [4].

A.2

Radio Local Area Networks equipment operating in the 5 GHz frequency band

5 GHz high performance RLAN systems are those within the scope and compliant with EN 301 893 [5].

A.3

Broadband Data Transmitting Systems operating in the band 5 725 MHz to 5 875 MHz

Broadband Data Transmitting systems are those within the scope and compliant with EN 302 502 [6].

ETSI

15ETSI EN 301 489-17 V1.3.2 (2008-04)

Annex B (informative):

The EN title in the official languages

Language EN title Bulgarian Електромагнитна съвместимост и въпроси на радиоспектъра (ERM). Стандарт за

електромагнитна съвместимост (EMC) на радиосъоръжения. Част 17: Специфични условия за широколентови системи за предаване на 2,4 GHz, висококачествени съоръжения за RLAN

локални радиомрежи за предаване на 5 GHz и широколентови системи за предаване на данни на 5,8 GHz Czech Elektromagnetická kompatibilita a rádiové spektrum (ERM) – Norma pro elektromagnetickou

kompatibilitu (EMC) rádiových zařízení a služeb – Část 17: Specifické podmínky pro širokopásmové přenosové systémy 2,4 GHz, vysokovýkonná zařízení RLAN 5 GHz a širokopásmové datové přenosové systémy 5,8 GHz

Danish Elektromagnetisk kompatibilitet og Radiospektrum Anliggender (ERM); Elektromagnetisk kompatibilitet

(EMC) for radioudstyr; Del 17: Særlige krav til 2,4 GHz bredbånds transmissionssystemer, 5 GHz højtydende RLAN udstyr samt 5,8 GHz bredbånds datatransmissionsudstyr

Dutch Elektromagnetische compatibiliteit en radiospectrumaangelegenheden (ERM);Elektromagnetische

compatibiliteit (EMC) norm voor radioapparatuur ;Deel 17 Specifieke omstandigheden voor de 2,4 GHz breedband transmissiesytemen, 5 GHz hoge-prestatie RLAN apparatuur en 5,8 GHz breedband gegevenstransmissiesytemen

English Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility

(EMC) standard for radio equipment; Part 17: Specific conditions for 2,4 GHz wideband transmission systems, 5 GHz high performance RLAN equipment and 5,8 GHz Broadband Data Transmitting Systems

Estonian Elektromagnetilise ühilduvuse ja raadiospektri küsimused ERM); Raadioseadmete elektromagnetilise

ühilduvuse (EMC) standard; Osa 17: Eritingimused raadiosagedusalas 2,4 GHz lairiba

edastussüsteemidele, raadiosagedusalas 5 GHz suure edastuskiirusega RLAN seadmetele ja 5,8 GHz lairiba andmeedastussüsteemidele

Finnish Sähkömagneettinen yhteensopivuus ja radiospektriasiat (ERM); Sähkömagneettinen

yhteensopivuusstandardi radiolaitteille; Osa 17: Erityisehdot 2,4 GHz:n, 5 GHz:n ja 5,8 GHz:n laajakaistaisille datasiirtojärjestelmille

French Télécommunications - CEM et spectre radioélectrique (ERM) - Partie 17 : conditions spécifiques pour

les systèmes de transmission à large bande de 2,4 GHz, les équipements de haute performance RLAN de 5 GHz et les systèmes de transmission à large bande de 5,8 GHz

German Elektromagnetische Verträglichkeit und Funkspektrumangelegenheiten (ERM) - Elektromagnetische

Verträglichkeit für Funkeinrichtungen und -dienste - Teil 17: Spezifische Bedingungen für

Breitbandübertragungssysteme im 2,4 GHz Band, Einrichtungen in lokalen Hochleistungs-Funknetzen (RLAN) im 5 GHz Band und Breitband-Datenübertragungssysteme im 5,8 GHz Band

Greek Ηλεκτρομαγνητική συμβατότητα και Θέματα Ραδιοφάσματος (ERM) – Πρότυπο Ηλεκτρομαγνητικής

Συμβατότητας (EMC) για ραδιοεξοπλισμό και ραδιοϋπηρεσίες – Μέρος 17: Είδιες συνθήκες για

ευρυζωνικά συστήματα μετάδοσης 2,4 GHz, εξοπλισμό RLAN υψηλής επίδοσης 5 GHz και συστήματα μετάδοσης ευρυζωνικών δεδομένων 5,8 GHz Hungarian Elektromágneses összeférhetőségi és rádióspektrumügyek (ERM). Rádióberendezések

elektromágneses összeférhetőségi (EMC) szabványa. 17. rész: A 2,4 GHz-es széles sávú átviteli

rendszerek, az 5 GHz-es nagy teljesítőképességű RLAN-berendezések és az 5,8 GHz-es széles sávú adatátviteli rendszerek sajátos feltételei

Icelandic Þættir sem varða rafsegulsviðssamhæfi og fjarskiptatíðni (ERM); Staðall um rafsegulsviðssamhæfi

(EMC) fyrir þráðlausan fjarskiptabúnað; 17. hluti: Sérstök skilyrði um 2,4 GHz víðbandssendingarkerfi og 5 GHz hágæða RLAN búnað og 5,8 GHz breiðbandsgagnasendingarkefi

Italian Compatibilità elettromagnetica e questioni relative allo spettro delle radiofrequenze (ERM); Norma di

compatibilità elettromagnetica (EMC) per apparati radio; Parte 17: Condizioni specifiche per sistemi di trasmissione a banda larga nella banda 2,4 GHz, per apparecchiature RLAN ad alte prestazioni nella banda 5 GHz e per sistemi che trasmettono dati a banda stretta nella banda 5,8 GHz

Latvian Elektromagnetiska saderiba un radiofrekvencu spektra jautajumi (ERM). Radioiekartu

elektromagnetiskas saderibas (EMC) standarts; 17. dala: Ipašie nosacijumi 2,4 GHz plašjoslas

parraides sistemam, 5 GHz augstas veiktspejas vietejo radiopiekluves tiklu (RLAN) iekartam un 5,8 GHz platjoslas datu parraides sistemam

Lithuanian Maltese Kompatibilità elettromanjetika u materji relatati ma' spettru radjofoniku (ERM); Standard ta’

Kompatibilità ElettroManjetika (EMC) għal tagħmir radjofoniku; Parti 17: Kondizzjonijiet speċifiċi għal sistemi ta’ trasmissjoni fuq frekwenza wiesgħa 2,4 GHz, tagħmir RLAN ta’ kapaċità operattiva għolja 5 GHz u sistemi li jittrasmettu data fuq frekwenza 5,8 GHz

ETSI

16ETSI EN 301 489-17 V1.3.2 (2008-04)

Language EN title Norwegian Elektromagnetisk kompatibilitet og radiospektrumsaker (ERM); Elektromagnetisk kompatibilitet (EMC)

standard for radioutstyr; Del 17: Spesifikke forhold for 2,4 GHz bredbnds transmisjonssystemer, 5 GHz hyytelses RLAN-utstyr og 5,8 GHz bredbnds transmisjonssystemer

Polish Kompatybilność elektromagnetyczna i zagadnienia widma radiowego (ERM) – Norma kompatybilności

elektromagnetycznej (EMC) dotycząca urządzeń radiowych - Część 17: Warunki określone dla szerokopasmowych systemów transmisyjnych o częstotliwości 2,4 GHz, urządzeń RLAN wysokiej jakości o częstotliwości 5 GHz i szerokopasmowych systemów w transmisji danych o częstotliwości 5,8 GHz

Portuguese Romanian Slovak Elektromagnetická kompatibilita a záležitosti rádiového spektra (ERM). Elektromagnetická

kompatibilita (EMC), norma na rádiové zariadenia. Časť 17: Osobitné podmienky na širokopásmové prenosové systémy v pásme 2,4 GHz, zariadenia vysokovýkonnej RLAN v pásme 5 GHz a širokopásmové dátové prenosové systémy v pásme 5,8 GHz

Slovenian Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Standard

elektromagnetne združljivosti (EMC) za radijsko opremo - 17. del: Posebni pogoji za širokopasovne prenosne sisteme na frekvenci 2,4 GHz, visokozmogljivo opremo RLAN na frekvenci 5 GHz in širokopasovne sisteme za prenos podatkov na frekvenci 5,8 GHz

Spanish Swedish Elektromagnetisk kompatibilitet och radiospektrumfrgor (ERM), Elektromagnetisk

kompatibilitetsstandard (EMC) fr radioutrustning och tjnster; Del 17: Specifika villkor fr 2,4 GHz bredbands transmissionssystem och 5 GHz hg prestanda RLAN-utrustning

ETSI

17ETSI EN 301 489-17 V1.3.2 (2008-04)

Annex C (informative): Bibliography

•

ETSI ETS 300 836-1: \"Broadband Radio Access Networks (BRAN); HIgh PErformance Radio Local Area Network (HIPERLAN) Type 1; Conformance testing specification; Part 1: Radio type approval and Radio Frequency (RF) conformance test specification\".

ETSI

18ETSI EN 301 489-17 V1.3.2 (2008-04)

History

Document history

V1.1.1 September 2000 Publication V1.2.1 August 2002 Publication V1.3.1 V1.3.2 V1.3.2

April 2007 June 2007 February 2008

One-step Approval Procedure

(Withdrawn) Public Enquiry Vote

OAP 20070824: 2007-04-25 to 2007-08-24 PE 20071005: 2007-06-06 to 2007-10-05 V 20080411: 2008-02-11 to 2008-04-11

V1.3.2 April 2008 Publication

ETSI

因篇幅问题不能全部显示，请点此查看更多更全内容

查看全文

全部栏目

EN301489-17 V1.3.2-2008