1……………………..封 面 2……………………..生 產 圖 面
3……………………..插 頭 圖 面(SP-506A) 4……………………..插 尾 圖 面(IS-14) 5……………………..安 規 規 格 6……………………..信 賴 性 實 驗 7……………………..相 關 國 家 証 明 書
I-SHENG M F G （SONGGANG） FACTORY
SPECIFICATION
ISSUED2008.8.6REVISED 1.SCOPE: THIS SPECIFICATION IS APPLIED TO POWER SUPPLY CORDS. REFERENCE PUBLICATIONS: GB1002-96 GB2099.1-96 GB5023-97 GB17465.1-98 2.CONSTRUCTION AND DIMENSIONS: IN ACCORDANCE WITH THE FOLLOWING TABLES AND ATTACHED DRAWINGS. TABLE 1. STD.NAMECAT NO. CCC APPROVAL POWER SUPPLY CORD FILE NO.506A-14-75-C PAGE2SP-506A+IS-14 RVV 300/500V 3G 0.75mm1ITEMPLUGCAT NOSP-506ARATINGA10V250250APPROVED NO.CCC20070101012320002007010101232000 RVV 300/500V 3G 0.75mm2 CONNECTORIS-1410 TABLE 2.FLEXIBLE CORDAPPROVED NO.RATINGNO.OF CORE (COLOR OF CORE)CONDUCTORNOMINAL (mm2)CONSTRUCTION (pcs/mm)MEAN VALUE OF THICKNESS (mm)INSULATION2007010101232000300/500V 3 (BLUE,BROWNYELLOW/GREEN)0.75mm224/Φ0.2+0/-0.0150.600.44Φ2.35±0.10.800.58Φ6.7±0.2MIN. THICKNESS AT ANY POINT (mm)NOMINAL OVERALL DIAMETER (mm)MEAN VALUE OF THICKNESS (mm)SHEATHMIN. THICKNESS AT ANY POINT (mm)NOMINAL OVERALL DIAMETER (mm) (NOTE: IF THE CONDUCTOR'S O.D IS GO BEYOND THE SCOPE, THE RESISTANCE OF CONDUCTOR IS STANDARD THEN.) 3. WIRE MARKING: PRINTING ON THE SHEATH 1) I-SHENG SGIS VDE KEMA-KEUR VE △ CEBEC 809 NF-USE 1346 IEMMEQU H05VV-F 3G 0.75mm 3ASL/75 Q88228 A003083 60227 IEC 53 RVV 300/500V 2) I-SHENG KSIS VDE KEMA-KEUR VE △ CEBEC 809 NF-USE 1353 IEMMEQU H05VV-F 3G 0.75mm 3ASL/75 Q88228 A041481 60227 IEC 53 RVV 300/500V REMARK: 1)SGIS WIRE MARKING . 2) KSIS WIRE MARKING22 A Qiang C Yun D Kikiµo¦æ ISSUED
I-SHENG ELECTRIC WIRE & CABLE CO., LTD.
SPECIFICATION
THE CHARACTERISTIC OF POWER SUPPLY CORD
FOR CHINA
ÀÉ®×½s¸¹FILE NOSPEC-CNSpecification³W®æ
¼Ð·Ç¦WºÙ
2000.03.05STD.NAME-×-q REVISEDÃD¥Ø2005.09.28TITLE
ItemsConditions¶µ¥Ø±ø¥ó
1Insulation resistanceApply a voltage of 500 (+250,-Between two0) V DC for 1 min. at anconductorsµ´½t©è§Ü
ambient temperature of 20¢J,¾ÉÅé¬Û¤¬¶¡
after which measurement shallBetween a conductorbe made.and ground
¾ÉÅé¤j¦a¶¡
100M£[or more
100M£[¥H¤W
2Electric strength-@¹qÀ£
Testing transformer capacity(-@À£-p®e¶q):500 VA or moreTrip current(¾BÂ_¹q¬y):2mAfrequency(©Pªi¼Æ):50/60 Hz
Between twoConductors2800V/1min.¾ÉÅé¬Û¤¬¶¡,1¤ÀBetween conductor andground 2800V/1min.¾ÉÅé¤j¦a¶¡,1¤À
Between conductorsAnd outside body 4000Without breakdown or
flashover shall occurV/1 min.
¨S¦³·lÃa¾ÉÅéªí-±¶¡, 1¤À
µo¦æ ISSUED
I-SHENG ELECTRIC WIRE & CABLE CO., LTD.
SPECIFICATION
THE CHARACTERISTIC OF POWER SUPPLY CORD
FOR CHINA
ÀÉ®×½s¸¹FILE NOSPEC-CN
¼Ð·Ç¦WºÙ
2000.03.05STD.NAME-×-q REVISEDÃD¥Ø2005.09.28TITLE
Items¶µ¥Ø
Flexing test©}¦±±j«×
3Conditions±ø¥ó
This test shall be made at an ambient temperature of25±5¢J to examine the strength of protectors of theattachment plug and the cord connector.
Load Weight
(g)
0.75mm2¡õ1020(10N)
plug1.0mm2¡ô
2040(20N)0.75mm2¡õ1020(10N)
connector
1.0mm2¡ô2040(20N)
Minor
Angleaxis
0
£c()direction
(turns)
Optionaldirection(turns)
Furthermore
Rate of
90¢Xrotational
flexing per
directionmin (turns)(turns)
4510000500060
Specification³W®æ
After the test thesample shall show nodamage except thatbreakage of no morethan 10% of the totalnumber of conductorstrands in any core isignored provided theyhave not pierced theinsulation.
45200001000060
A sample of flexing cord shall be fixed in the apparatusas shown in the above.
The sample shall be bent backwards and forwards on adirection perpendicular to the plan of the axis of theconductors, the two extreme positions marking thespecified angle on both side of the vertical.
The attachment plug end or cord connector end shall beplaced in the center of the swinging board.
The specified weight shall be suspended from the cordand the board shall swing be specified times at thespecified rate, making a one way bending one cycle.
µo¦æ ISSUED
I-SHENG ELECTRIC WIRE & CABLE CO., LTD.
SPECIFICATION
THE CHARACTERISTIC OF POWER SUPPLY CORD
FOR CHINA
ÀÉ®×½s¸¹FILE NOSPEC-CN
¼Ð·Ç¦WºÙ
2000.03.05STD.NAME-×-q REVISEDÃD¥Ø2005.09.28TITLE
Items¶µ¥Ø
Withdrawal force¤Þ©Þ¤O
4Conditions±ø¥ó
Withdraw the cord connector straight into (or form) thestandard gauge.
Verification of the maximum withdrawal force
The connector is inserted to the full depth into and
withdrawn from the appropriate appliance inlet 10 times.It is then again inserted for a principal mass is such thatit exerts a force equal to one-tenth of the maximumwithdrawal force specified in the table and it shall bemade one piece and a supplementary
Verification of the minimum withdrawal force
Is applied to each individual connector contact with thecontact axes vertical and the gauge hanging verticallydownwards. The total mass of the gauge shall be suchas to exert the applicable force as show in table.
Withdrawal forceN( kg )
Multi-pin gaugeSingle-pin gaugeminimummaxMin50
( 5.1 )
10 ( 1.0 )
1.5( 0.15 )
Type of
connector
0.2A2.5A6A10A16A
60( 6.1 )15( 1.5 )2( 0.2 )
Specification³W®æ
After Verification ofthe maximum
withdrawal force test.The principal mass ishung on the
connector withoutjolting and the
supplementary massis allowed to fall froma height of 5 cm on tothe principal mass.The connector shallnot remain in theappliance inlet.After Verification ofthe minimum
withdrawal force test.The test pin gauge isapplied gently, andcare is taken not toknock the assemblywhen checking theminimum withdrawalforce. The gauge shallnot fall from thecontact assemblywithin 3 sec.
µo¦æ ISSUED
I-SHENG ELECTRIC WIRE & CABLE CO., LTD.
SPECIFICATION
THE CHARACTERISTIC OF POWER SUPPLY CORD
FOR CHINA
ÀÉ®×½s¸¹FILE NOSPEC-CN
¼Ð·Ç¦WºÙ
2000.03.05STD.NAME-×-q REVISEDÃD¥Ø2005.09.28TITLE
Items¶µ¥Ø
Temperature riseၻ@
5ConditionsSpecification±ø¥ó³W®æ
An alternating current of 1.25 times rated current isThe temperature risepassed through the current-carrying contacts for 1hof terminals andFor connectors with earthing contact, the current is thencontacts shall notpassed through one current-carrying contact and theexceed 45kearthing contact for 1h
6Breaking capacityThe connector and appliance inlet are connected andThe specimen shalldisconnected 50 times (100 strokes) at a rate of 30show no damage±ÒÂ_®e¶q
strokes per minute. The length of a stroke of the testimpairing its furtherapparatus is between 50mm and 60mmuse and the entryThe periods during which the test current is passed fromholes for the pin shallthe connection to the subsequent disconnection of thenot show any seriousaccessories are 1.5(+0.5,-0)sdamage.The test voltage is 275V, the test current is 1.25 timesrated current and the power factor is at least 0.95 for 10Aand 16A connectors and 0.6¡Ó0.05 for other connectors
7Resistance to heatTest being made in a heating cabinet at a temperature ofAfter 1h, the jaws areremoved and the-@¼ö¸ÕÅç100 ¡Ó2¢J
The specimen is clamped between steel jaws, having aspecimen shall showcylindrical face of 25mm radius, a width of 15mm and ano damage within thelength of 50mm. The corners are rounded with a radiusmeaning of this
standard.of 2.5mm.
The specimen is clamped in such a way that the jawspress against it in the area where it is gripped in normaluse, the centre line of the jaws coinciding as nearly aspossible with the centre of this area.
The force applied through the jaws is 20N
µo¦æ ISSUED
I-SHENG ELECTRIC WIRE & CABLE CO., LTD.
SPECIFICATION
THE CHARACTERISTIC OF POWER SUPPLY CORD
FOR CHINA
ÀÉ®×½s¸¹FILE NOSPEC-CN
¼Ð·Ç¦WºÙ
2000.03.05STD.NAME-×-q REVISEDÃD¥Ø2005.09.28TITLE
ItemsConditionsSpecification¶µ¥Ø±ø¥ó³W®æ
8Resistance to AgingThe specimens are suspended freely in a heatingAfter this test, thecabinet, ventilated by natural circulation. They are kept inspecimen shall show¦Ñ¤Æ¸ÕÅç
the cabinet, which is maintained at a temperature of 80no damage which
would lead to non-¡Ó2¢J, for 168h (7 days).
After the test are allowed to attain approximately ambientcompliance with this
standard.temperature and are examined. They shall show no
crack visible to the naked eye, nor shall the materialhave become sticky or greasy, this being judged asfollows
A forefinger wrapped in a dry piece of rough cloth ispressed on the specimen with a force of 5N.
No traces of the cloth shall remain on the specimen andthe material of the specimen shall not stick to the cloth9Moisture resistanceThe humidity treatment is carried out in a humidityAfter this treatment,cabinet containing air with a relative humidity maintainedthe specimen shall-@Àã©Ê
between 91% and 95% The temperature of the air, at allshow no damage.places where specimens can be located, is maintainedwithin ¡Ó1¢J of any convenient value t¢J between 20¢Jand 30¢J
Before being placed in the humidity cabinet, the
specimens are brought to a temperature between t¢Jand ( t+4 ) ¢J
The specimens are kept in the cabinet for
- 168h (7 days) for connector with earthing contact andfor appliance inlets with earthing contact, which aresubmitted as individual accessories, not incorporated inother equipment.
- 48h (2 day) in all other cases.
µo¦æ ISSUED
I-SHENG ELECTRIC WIRE & CABLE CO., LTD.
SPECIFICATION
THE CHARACTERISTIC OF POWER SUPPLY CORD
FOR CHINA
ÀÉ®×½s¸¹FILE NOSPEC-CN
¼Ð·Ç¦WºÙ
2000.03.05STD.NAME-×-q REVISEDÃD¥Ø2005.09.28TITLE
ItemsConditionsSpecification¶µ¥Ø±ø¥ó³W®æ
10Mechanical strengthAfter the connector’s point is fixed as shown in the figureAfter the test, the
of connector bodybelow.connector shall show
A lateral pull, as specified in table, is applied to the cordno damage.first in a direction perpendicular to the plane containingthe axes of the current-carrying pin, and hall be appliedvertically and slowly for 60 sec.
This sequence of operation is made 1 time in onedirection and then 1 time in the opposite direction.
Rated current of connectorA2.561016N6353550Pull( Kg )( 0.61)( 3.57 )( 3.57 )( 5.1 )11Polarity/ContinuityLine and neutral shall be test at 24V;shall beinstantaneous
Without breakdown
因篇幅问题不能全部显示，请点此查看更多更全内容